TanklessCalc

Guide

Does a gas tankless water heater need electricity?

Yes, a little, all the time. Without it there is no hot water.

Short answer

Yes. A gas tankless water heater burns gas for heat but needs 120 V electricity to light the burner, run the combustion fan and work the controls. The draw is small: the RU199i, a 199,000 BTU Rinnai, uses 84 W while heating, 1.3 W on standby and up to 148 W when its freeze protection runs. With the power off it will not fire, so a power cut means no hot water.

Size a gas tankless for your house

What the electricity does

  • Ignition. There is no standing pilot. Rinnai RU-series (Sensei) units use direct electronic ignition, which sparks the burner each time hot water is drawn.
  • The combustion fan. The fan pushes exhaust out through the vent, and the unit checks its speed. No fan, no burner.
  • Controls and sensors. A flow sensor tells the unit a tap is open, and the board modulates the gas to hold your set temperature. The wall controller runs on 12 V DC.
  • Freeze protection. In cold weather the unit warms its own water passages electrically to keep them from freezing. This is the largest draw.

How many watts a gas tankless uses

Rinnai RU-series (Sensei) specification sheet, 120 V AC, 60 Hz
ModelGas inputHeatingStandbyFreeze protection
RU199i199,000 BTU84 W1.3 W148 W
RU180i180,000 BTU65 W1.3 W148 W
RU160i160,000 BTU52 W1.3 W148 W
RU130i130,000 BTU38 W1.3 W148 W

The same sheet lists a maximum current of 4 A and a 10 A internal fuse. Other brands publish their own figures in the installation manual, under electrical specifications; check the one for your model, especially if it has a built-in recirculation pump, which draws more.

Next to the gas, the electricity is a rounding error. The RU199i burns 199,000 BTU an hour, which is 58.3 kW of gas, against 84 W of electricity: 0.14% of the energy going through it. A household whose heater fires for 1 hour a day at full draw and sits on standby the rest of the time uses about 3.4 kWh of electricity a month for it.

What happens in a power outage

The heater stops. With no power there is no spark, no fan and no flow sensor, so the gas valve stays shut and the taps run cold. Gas tank heaters with a standing pilot and a thermocouple-powered gas valve are the ones that keep working in an outage; a tankless unit is not one of them.

The bigger risk is frost. Freeze protection is electric too, so an outage in freezing weather leaves the water inside the heater unprotected. Rinnai’s manual for the RV53E says that if power is lost, or the cold is beyond what the freeze protection handles, you should turn the unit off, close the gas supply and let a tap run at a very low flow, about 0.1 GPM, to keep water moving through it. For freezing weather without power, it says to drain the unit: shut off the cold water and gas, turn the controller off, disconnect the power and open the drain plugs. Do not try to run a heater that has frozen until it has been checked.

Running it from a battery or generator

The load is small enough for a portable power station or a small generator. A 1,000 Wh battery could in principle run an RU199i for about 12 hours of burner time, or its freeze protection for about 7 hours, before inverter losses, which take a share of that. Two things matter more than the size of the battery:

  • Grounding. The heater needs a grounded 120 V supply, from a battery or generator as much as from the wall. Check what the installation manual says about generator power before relying on it.
  • How it is wired. If the heater plugs in, you can move the plug. If it is hard-wired to a junction box, it needs a transfer switch or an interlock fitted by an electrician.

The outlet and circuit it needs

An ordinary grounded 120 V supply. A 4 A maximum is 27% of a 15 A circuit, so the heater does not need a heavy circuit of its own the way an electric tankless does. Whether it plugs into an outlet or is wired into a junction box, and whether it may share a circuit, is set by the installation manual and your local code. For what an electric tankless needs instead, see what size breaker a tankless water heater needs.

Frequently asked questions

Can a gas tankless water heater work without electricity?
No. It needs power to spark the burner, run the combustion fan and read the flow sensor. In a power cut the gas valve stays closed and the water runs cold.
How many watts does a gas tankless water heater use?
Very few. Rinnai’s spec sheet lists 84 W for the RU199i, 65 W for the RU180i, 52 W for the RU160i, 38 W for the RU130i while heating, 1.3 W on standby and 148 W with freeze protection on.
Will a tankless water heater work during a power outage?
Not on its own, gas or electric. A gas unit runs from a small generator or a battery power station if it can be connected safely; an electric unit draws far too much for that.
Does a gas tankless water heater need a dedicated circuit?
Its draw is small, a 4 A maximum on the Rinnai RU series. Whether it can share a circuit is set by the installation manual and local code, so check both before plugging it into an existing outlet.
Do I need an outlet for a tankless water heater?
A gas unit needs a grounded 120 V supply: an outlet if the unit has a cord, a junction box if it is hard-wired. An electric tankless needs 240 V circuits from the panel instead, wired directly.
How much electricity does a gas tankless use a month?
A few kilowatt-hours. A RU199i firing 1 hour a day at 84 W, on 1.3 W standby otherwise, uses about 3.4 kWh a month. Freeze protection in winter adds to that.
Can a tankless water heater freeze if the power goes out?
Yes. Freeze protection is electric. Rinnai’s manual says to turn the unit off, close the gas and run a tap at about 0.1 GPM, or drain the unit if it will be without power in freezing weather.
Does a gas tank water heater need electricity?
One with a standing pilot and a thermocouple gas valve does not, which is why it keeps heating in an outage. Power-vent and electronic-ignition tanks do need power.

Work it out for your own project